Model name	Rated input voltage	Enclosure ratings	Max. applicable motor capacity
Model name	Rated input voltage	Enclosure ratings	CT: Heavy load	VT: Light load
3G3MX2-A2001-ZV1	3-phase AC200V	IP20	0.1kW	0.2kW
3G3MX2-A2002-ZV1			0.2kW	0.4kW
3G3MX2-A2004-ZV1			0.4kW	0.75kW
3G3MX2-A2007-ZV1			0.75kW	1.1kW
3G3MX2-A2015-ZV1			1.5kW	2.2kW
3G3MX2-A2022-ZV1			2.2kW	3.0kW
3G3MX2-A2037-ZV1			3.7kW	5.5kW
3G3MX2-A2055-ZV1			5.5kW	7.5kW
3G3MX2-A2075-ZV1			7.5kW	11kW
3G3MX2-A2110-ZV1			11kW	15kW
3G3MX2-A2150-ZV1			15kW	18.5kW
3G3MX2-A4004-ZV1	3-phase AC400V	IP20	0.4kW	0.75kW
3G3MX2-A4007-ZV1			0.75kW	1.5kW
3G3MX2-A4015-ZV1			1.5kW	2.2kW
3G3MX2-A4022-ZV1			2.2kW	3.0kW
3G3MX2-A4030-ZV1			3.0kW	4.0kW
3G3MX2-A4040-ZV1			4.0kW	5.5kW
3G3MX2-A4055-ZV1			5.5kW	7.5kW
3G3MX2-A4075-ZV1			7.5kW	11kW
3G3MX2-A4110-ZV1			11kW	15kW
3G3MX2-A4150-ZV1			15kW	18.5kW
3G3MX2-AB001-ZV1	1-phase AC200V	IP20	0.1kW	0.2kW
3G3MX2-AB002-ZV1			0.2kW	0.4kW
3G3MX2-AB004-ZV1			0.4kW	0.55kW
3G3MX2-AB007-ZV1			0.75kW	1.1kW
3G3MX2-AB015-ZV1			1.5kW	2.2kW
3G3MX2-AB022-ZV1			2.2kW	3.0kW

Function name	Specifications
Enclosure ratings	Open type (IP20)
Control method	Phase-to-phase sinusoidal modulation PWM
Output frequency range	0.10 to 400 Hz (or 580 Hz in the high-frequency mode; restrictions apply)
Frequency precision	Digital command: ±0.01% of the max. frequency, Analog command: ±0.2% of the max. frequency (25±10°C）
Frequency setting resolution	Digital setting: 0.01 Hz, Analog setting: One-thousandth of the maximum frequency
Voltage/Frequency characteristics	V/f characteristics (constant/reduced torque) Sensorless vector control, V/f control with speed feedback
Overload current rating	Heavy load rating (CT): 150%/60 s Light load rating (VT): 120%/60 s
Instantaneous overcurrent protection	200% of the value of heavy load rating (CT)
Acceleration/Deceleration time	e 0.01 to 3600 s (linear/curve selection), acceleration/deceleration 2 setting available
Carrier frequency adjustment range	2 to 15 kHz (with derating)
Starting torque	200%/0.5 Hz (sensorless vector control)
External DC injection braking	Starts at a frequency lower than that in deceleration via the STOP command, at a value set lower than that during operation, or via an external input. (Level and time settable).
Protective functions	Overcurrent, overvoltage, undervoltage, electronic thermal, temperature error, ground fault overcurrent at power-on status, rush current prevention circuit, overload limit, incoming overvoltage, external trip, memory error, CPU error, USP error, communication error, overvoltage suppression during deceleration, protection upon momentary power outage, emergency cutoff, etc.
Frequency settings	Digital Operator External analog input signal: 0 to 10 VDC/4 to 20 mA, Modbus communication (Modbus-RTU)
RUN/STOP command	Digital Operator External digital input signal (3-wire input supported), Modbus communication (Modbus-RTU)
Multi-function input	7 points (Selectable from 59 functions）
Analog input	2 points (Voltage FV terminal: 10 bits/0 to 10 V, Current FI terminal: 10 bits/4 to 20 mA)
Pulse input	1 point (RP terminal: 32 kHz max., 5 to 24 VDC)
Multi-function output	2 points (P1/EDM, P2; selectable from 43 functions)
Relay output	1 point (1c contact: MC, MA, MB; selectable from 43 functions)
Analog output (Frequency monitor)	1 point (AM terminal: Voltage 10 bits/0 to 10 V) (Frequency, current selectable)
Pulse input	1 point (RP terminal: 32 kHz max., 5 to 24 VDC)
Drive Programming	Calculate, Logic, Control I/O and so on
Ambient operating temperature	-10 to 50°C (However, derating is required)
Ambient storage temperature	-20°C to 65°C
Ambient operating humidity	20% to 90% RH (with no condensation)
Vibration resistance	5.9 m/s2 (0.6G), 10 to 55 Hz
Application environment	At a maximum altitude of 1,000 m; indoors (without corrosive gases or dust)
Other option	DC reactor, AC reactor, radio noise filter, input noise filter, output noise filter, regenerative braking unit, Braking Resistor, etc.

*

广州瑞大工控自动化设备有限公司

OMRON 3G3MX2 Inverter Models